dmesg on Lemote Fulong

Linux version 2.6.28-rc8-fulong2f (root@loongson2f) (gcc version 4.4.0 20081130 (experimental) [trunk revision 142292] (Debian 20081130-1) ) #3 Sat Dec 20 16:24:50 CST 2008
busclock=66000000, cpuclock=800020000,memsize=256,highmemsize=256
console [early0] enabled
CPU revision is: 00006303 (ICT Loongson-2)
FPU revision is: 00000501
Checking for the multiply/shift bug... no.
Checking for the daddiu bug... no.
Determined physical RAM map:
 memory: 0000000010000000 @ 0000000000000000 (usable)
 memory: 0000000010000000 @ 0000000090000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00028000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x00004000
    0: 0x00024000 -> 0x00028000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat ffffffff80739ad0, node_mem_map 9800000001000000
  Normal zone: 560 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32208 pages, LIFO batch:7
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32208
Kernel command line: root=/dev/hda2 console=tty ide_core.ignore_cable=0 uca=0x50000000,0x1000000 splash quiet 
Primary instruction cache 64kB, VIPT, direct mapped, linesize 32 bytes.
Primary data cache 64kB, 4-way, VIPT, no aliases, linesize 32 bytes
Unified secondary cache 512kB 4-way, linesize 32 bytes.
PID hash table entries: 2048 (order: 11, 16384 bytes)
Console: colour dummy device 80x25
console handover: boot [early0] -> real [tty0]
Dentry cache hash table entries: 65536 (order: 5, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 4, 262144 bytes)
Memory: 505728k/524288k available (3991k kernel code, 17904k reserved, 1386k data, 240k init, 0k highmem)
Calibrating delay loop... 532.48 BogoMIPS (lpj=1064960)
Security Framework initialized
Mount-cache hash table entries: 1024
Checking for the daddi bug... no.
net_namespace: 1320 bytes
xor: measuring software checksum speed
   8regs     :  1916.000 MB/sec
   8regs_prefetch:  1592.000 MB/sec
   32regs    :  1640.000 MB/sec
   32regs_prefetch:  1492.000 MB/sec
xor: using function: 8regs (1916.000 MB/sec)
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:06.0: reg 10 io port: [0xb100-0xb1ff]
pci 0000:00:06.0: reg 14 32bit mmio: [0x4075000-0x40750ff]
pci 0000:00:06.0: reg 30 32bit mmio: [0x4040000-0x405ffff]
pci 0000:00:06.0: supports D1 D2
pci 0000:00:06.0: PME# supported from D1 D2 D3hot
pci 0000:00:06.0: PME# disabled
pci 0000:00:08.0: reg 10 32bit mmio: [0x000000-0xfffffff]
pci 0000:00:08.0: reg 14 32bit mmio: [0x4000000-0x403ffff]
pci 0000:00:08.0: reg 18 io port: [0xb300-0xb37f]
pci 0000:00:08.0: reg 30 32bit mmio: [0x4060000-0x406ffff]
pci 0000:00:08.0: supports D1 D2
pci 0000:00:0e.0: reg 10 io port: [0xb410-0xb417]
pci 0000:00:0e.0: reg 14 io port: [0xb000-0xb0ff]
pci 0000:00:0e.0: reg 18 io port: [0xb380-0xb3bf]
pci 0000:00:0e.0: reg 20 io port: [0xb280-0xb2ff]
pci 0000:00:0e.0: reg 24 io port: [0xb3c0-0xb3df]
pci 0000:00:0e.2: reg 20 io port: [0xb400-0xb40f]
pci 0000:00:0e.3: reg 10 io port: [0xb200-0xb27f]
cs5536 acc latency 0
pci 0000:00:0e.4: reg 10 32bit mmio: [0x4074000-0x4074fff]
pci 0000:00:0e.5: reg 10 32bit mmio: [0x4073000-0x4073fff]
pci 0000:00:0e.6: reg 10 32bit mmio: [0x4070000-0x4071fff]
pci 0000:00:0e.7: reg 10 32bit mmio: [0x4072000-0x4072fff]
slot: 6, pin: 1, irq: 36
slot: 8, pin: 1, irq: 38
NET: Registered protocol family 8
NET: Registered protocol family 20
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 4096 (order: 1, 32768 bytes)
TCP established hash table entries: 16384 (order: 4, 262144 bytes)
TCP bind hash table entries: 16384 (order: 3, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
msgmni has been set to 989
alg: No test for stdrng (krng)
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
sisfb: Video ROM not found
sisfb: Video RAM at 0x50000000, mapped to 0x9000000050000000, size 32768k
sisfb: MMIO at 0x60000000, mapped to 0x9000000060000000, size 256k
sisfb: Memory heap starting at 32160K, size 32K
sisfb: Detected SiS301C video bridge
sisfb: CRT1 DDC supported
sisfb: CRT1 DDC level: 2 
sisfb: Monitor range H 30-63KHz, V 56-77Hz, Max. dotclock 80MHz
sisfb: Default mode is 800x600x8 (60Hz)
sisfb: Initial vbflags 0x10000020
Console: switching to colour frame buffer device 100x37
sisfb: 2D acceleration is enabled, y-panning enabled (auto-max)
fb0: SiS 315PRO frame buffer device version 1.8.9
sisfb: Copyright (C) 2001-2005 Thomas Winischhofer
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing enabled
brd: module loaded
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:00:06.0: no PCI Express capability
eth0: RTL8169sc/8110sc at 0x9000000060075000, 00:11:11:11:19:0a, XID 18000000 IRQ 36
Uniform Multi-Platform E-IDE driver
amd74xx 0000:00:0e.2: UDMA100 controller
amd74xx 0000:00:0e.2: IDE controller (0x1022:0x209a rev 0x01)
amd74xx 0000:00:0e.2: IDE port disabled
amd74xx 0000:00:0e.2: not 100% native mode: will probe irqs later
ide: ignoring cable detection for ide0
    ide0: BM-DMA at 0x4ce0-0x4ce7
Probing IDE interface ide0...
hda: Hitachi HTS541612J9AT00, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
ide-gd driver 1.18
hda: max request size: 512KiB
hda: 234441648 sectors (120034 MB) w/7512KiB Cache, CHS=16383/255/63
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
Driver 'sd' needs updating - please use bus_type methods
usbcore: registered new interface driver libusual
i8042.c: No controller found.
Trying to free nonexistent resource <0000000000000060-000000000000006f>
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int64x1    387 MB/s
raid6: int64x2    541 MB/s
raid6: int64x4    605 MB/s
raid6: int64x8    488 MB/s
raid6: using algorithm int64x4 (605 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP bic registered
begin to find the vga mem range
find the frame buffer:start=50000000,end=5fffffff
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 240k freed
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:0e.4 to 64
ohci_hcd 0000:00:0e.4: OHCI Host Controller
ohci_hcd 0000:00:0e.4: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.4: irq 11, io mem 0x60072000
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
PCI: Setting latency timer of device 0000:00:0e.5 to 64
ehci_hcd 0000:00:0e.5: EHCI Host Controller
ehci_hcd 0000:00:0e.5: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0e.5: irq 11, io mem 0x60073000
ehci_hcd 0000:00:0e.5: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 2-2: new high speed USB device using ehci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
input: USB Optical Mouse as /class/input/input0
generic-usb 0003:15CA:00C3.0001: input: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:0e.4-1/input0
usb 1-3: new low speed USB device using ohci_hcd and address 3
usb 1-3: configuration #1 chosen from 1 choice
input:   SCISSORS Keyboard as /class/input/input1
generic-usb 0003:0DC6:3101.0002: input: USB HID v1.00 Keyboard [  SCISSORS Keyboard] on usb-0000:00:0e.4-3/input0
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
phy0: Selected rate control algorithm 'pid'
PCI: Setting latency timer of device 0000:00:0e.3 to 64
Registered led device: rt73usb-phy0:radio
Registered led device: rt73usb-phy0:assoc
Registered led device: rt73usb-phy0:quality
usbcore: registered new interface driver rt73usb
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
Adding 1020080k swap on /dev/hda3.  Priority:-1 extents:1 across:1020080k
EXT3 FS on hda2, internal journal
fuse init (API version 7.10)
r8169: eth0: link up
rt73usb 2-2:1.0: firmware: requesting rt73.bin
NET: Registered protocol family 17
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ioctl32(Xorg:2047): Unknown cmd fd(7) cmd(8004f300){t:'&#65533;';sz:4} arg(7fe16eec) on /dev/fb0
ioctl32(Xorg:2047): Unknown cmd fd(7) cmd(80046ef8){t:'n';sz:4} arg(00639d38) on /dev/fb0
eth0: no IPv6 routers present

Projects/GNewSenseToMIPSFulongDmesg (last edited 2009-01-31 18:57:13 by rm)